CHAR-LYNN (EATON) 103-1054-010
CHAR-LYNN (EATON)
CHAR-LYNN (EATON) 103-1054-010
103-1054-010 PART NUMBER
103-1054-012
MFR
Hydraulic Geroler Spool Valve Motor - S-Series, 13.7 in³/r, 4-Bolt Flange - 1.75 in Pilot
QTY QUOTECHAR-LYNN (EATON) - CHAR-LYNN (EATON) 103-1054-010
Constant clearance Geroler€š design
Three moving components (gerotor, drive, shaft)
Optimized drive running angle
Three-zone pressure design (inlet, return and case)
Variety of displacements, shafts and mounts
Special options to meet customer needs
SPECIFICATIONS
| Series | S-Series |
|---|---|
| Intermittent Flow Rate | 20 gpm |
| Displacement | 13.70 in³/r |
| Intermittent Pressure | 2050 psi |
| Maximum Rpm-Continuous | 253 rpm |
| Intermittent Torque | 3843 in-lbs |
| Continuous Torque | 3290 in-lbs |
| Replacement Buna Seal Kit - Sold Separately | 008 Design - 60533-000, 009 & 010 Design - 60539-000 |
| Continuous Pressure | 1700 psi |
| Replacement Viton Seal Kit - Sold Separately | 008 Design - 60534-000, 009 & 010 Design - 60546-000 |
| Continuous Flow Rate | 15 gpm |
| Replacement Bearing Race - Sold Separately | 008, 009 & 010 Design - 7462-000 |
| Motor Port Type | National Pipe Tapered Fuel |
| Replacement Needle Thrust Bearing | 008, 009 & 010 Design - 7537-000 |
| Motor Port Size | 1/2?14 NPTF |
| Replacement Output Shaft - Sold Separately | 008, 009 & 010 Design - 7360-002 |
| Shaft Type | Splined |
| Replacement Geroler - Sold Separately | 010 Design - 8632-025 |
| Output Shaft Size | 1 in SAE - 6B Spline |
| Replacement Drive - Sold Separately | 010 Design - 22190-000 |
| Mounting Type | 4-Bolt Flange - 1.75 in Pilot |
| Replacement Short Cap Screw (Mounting End) - Sold Separately | 008, 009 & 010 Design - 16292-088 - 4 Required |
| Seal Type | Standard |
| Replacement Long Cap Screw (Cap End) - Sold Seprately | 010 Design - 16294-238 - 7 Required |
| Case Drain | No Case Drain |
| Replacement Rear Housing - Sold Separately | 008, 009 & 010 Design - 8631-002 |
| Inlet And Outlet Port Size | 1/2-14 NPTF Ports Size 8MP |
| Replacement Mounting Flange - Sold Separately | 010 & 009 Design 22000-002, 008 Design 7464-000 |
| Actual Port Type | .500-14 Nptf Dryseal Pipe thread Accepts Dryseal Fittings Per Sae J476A |
| Repair Parts Drawing# | 6-125 |
| Actual Output Shaft | 25.4 [1.00] Sae 6B Spline With 1/4-20 Threaded Hole |
| Manufacturer Product Page | http://www.eatonpowersource.com/products/configure/motors/details/103-1054-012/ |
| Actual Mounting Flange | 4 Bolt Std: 44.4 [1.75] Dia. X 3.0 [.12] Pilot, .375-16 Mounting |
| Maximum Operating Temperature | 180 °F |
| Overall Length | 159.4 mm |
| Overall Width | 107.7 mm |
