CHAR-LYNN (EATON) 158-3201-001
CHAR-LYNN (EATON)
CHAR-LYNN (EATON) 158-3201-001
158-3201-001 PART NUMBER
Hydraulic Geroler Spool Valve Motor - T-Series, 11.9 in³/r, 2-Bolt Flange - 3.25 in Pilot
QTY QUOTECHAR-LYNN (EATON) - CHAR-LYNN (EATON) 158-3201-001
Constant clearance Geroler‚ geometry
Optimized drive system with reduced running angle
Three-pressure zone design, (ability to reduce case pressure)
Variety of displacements, shafts and mounts
Special options to meet customer needs
SPECIFICATIONS
| Series | T-Series |
|---|---|
| Intermittent Pressure | 2500 psi |
| Displacement | 11.90 in³/r |
| Intermittent Torque | 3864 in-lbs |
| Maximum Rpm-Continuous | 287 rpm |
| Replacement Buna Seal Kit - Sold Separately | 001 Design - 60564-000 |
| Continuous Torque | 3178 in-lbs |
| Replacement Viton Seal Kit - Sold Separately | 001 Design - 60565-000 |
| Continuous Pressure | 2000 psi |
| Replacement Bearing Race - Sold Separately | 001 Design - 7462-000 |
| Continuous Flow Rate | 15 gpm |
| Replacement Needle Thrust Bearing | 001 Design 7537-000 |
| Motor Port Type | Straight Thread O-Ring SAE |
| Replacement Output Shaft - Sold Separately | 001 Design - 7360-001 |
| Motor Port Size | 7/8?14 UNF-2B |
| Replacement Geroler - Sold Separately | 001 Design - 22801-008 |
| Shaft Type | Straight |
| Replacement Drive - Sold Separately | 001 Design - 201111-006 |
| Output Shaft Size | 1 in Straight - Woodruff Key |
| Replacement Short Cap Screw (Mounting End) - Sold Separately | 001 Design - 16292-088 - 4 Required |
| Mounting Type | 2-Bolt Flange - 3.25 in Pilot |
| Replacement Long Cap Screw (Cap End) - Sold Seprately | 001 Design - 16294-262 - 7 Required |
| Seal Type | High Pressure |
| Replacement Rear Housing - Sold Separately | 001 Design - 201285-001 |
| Case Drain | No Case Drain |
| Replacement Mounting Flange - Sold Separately | 001 Design - 22000-001 |
| Inlet And Outlet Port Size | Straight Thread O-ring SAE 7/8-14 UNF-2B Ports Size 10 |
| Repair Manual# | 7-1450 |
| Actual Port Type | .875-14 Unf-2B O-ring Port, Size 10 Accepts Fittings For Sae J1926 |
| Repair Parts Drawing# | 6-146 |
| Actual Output Shaft | 25.4 [1.00] Dia. Straight With Woodruff Key And .250-20 Unc-2B Threaded Hole |
| Manufacturer Product Page | http://www.eatonpowersource.com/products/configure/motors/details/158-3201-001/ |
| Actual Mounting Flange | Standard, 2 Bolt: 82.6 [3.25] Dia. X 3.0 [.12] Pilot, 13.59 [.535] Dia. Holes On 106.2 [4.18] Dia. Bolt Circle |
| Maximum Operating Temperature | 180 °F |
| Intermittent Flow Rate | 20 gpm |
